簡要

Summary

圈圓機是產出石材圈圓的公用設施法寶，為三滾式圈圓機。其調整布局秉公、研究生調劑友盒、產出效應高、操控簡化，并可在圈圓tcp連接中圈壓出對氬弧焊口處兩直邊，為下一家道工序對焊奪取杰出青年的壓根, 材質壁厚不夸越4.5mm。This coiler machine is special equipment that is used for steel plate coiling. It has reasonable structure with 3 rollers type design, convenient adjustment, high efficiency and simple operation, and also it can press out straight flange on the two sides of welding joint in the coiling process to lay a good foundation for the next working procedure butt welding except the material exceed 4.5mm.

該極品裝備有著印刷和壓平的兩重功較。此中印刷用以在輪輞板料毛坯房上壓出所需用的記號，如輪輞的規格、具體型號、盛產公司、盛產時間日期等一等，壓平則是為未來發展對焊。This is special equipment for rim production, which has dual function of stamping and flattening. The stamper of it is used to press the needed marks on the rim band, including specification, model, manufacturer, production date etc. It flattens weld joint for the following welding operation.

重中之重加工廠繁瑣流程是：自動裝料à彩印à圈圓à壓平管道焊接Automatic operating for feeding-stamping-coiling-flattening weld joint

法寶功能分區簡價

Equipment Structure Introduction

設備由被動送料機機購、打字機購、卷圓機和壓平機購四局部性構造。The equipment includes four parts：automatically feeder, stamper, coiler and flattening device.

放卷臺由形鋼補焊而成，上置鋁鋁合金放卷金屬支架，使用放卷主動權送進。The feeding platform is welded with structure steel, on which place aluminous feeding rack for material automatically feeding.

印刷機機由強弱倆個壓紋輥組成部分，印刷機用的字頭裝鄙人壓延機，可據需很便捷性的更調。當給料進壓紋輥內時，激勵壓紋輥起頭彈出，將鋼字順次壓紋在板料上，并將壓紋好的板料輸送，隨著壓紋輥通過工作氣式積極主動規復原位，為了能讓滿足反差板厚的懇求，兩壓紋輥的接縫處才能手工diy食補。The stamper is made of upper and lower roller. The marking unit is installed on the lower roller, which is easy to change by requirement. When the steel card is feed into the press-stamping roller, push roller to make it roll and stamp steel letters on the band one by one then push out the finished band, the press-stamping roller will back to the home position by the cylinder. The gap between two rollers can be adjusted manually to meet different band thickness.

重要性規格

Main Parameter

轉備產品型號	Model Number	Номер модели	JYJ-600-AH
材料重量	material thickness	Толщина обода	≤4.5mm
工件表面尺寸	Rim Width	Ширина обода	≤320mm
長度大規模	Rim Diameter Range	Диаметр обода	300mm~500mm
模擬輸出電功率	input capacity	Общая мощность	14KW

技藝特殊性

設備的電子商務工作管理體制由可邏緝吃妻上癮器PLC、實戰器、交流電機驅動器電機、電機驅動器工作管理體制、機電工程專業和各檢查傳調節器器組合。吃妻上癮器得到德力西M218產品系列，德力西M218 PLC體積太小、效率快、正規化，擁有串口通信網絡就可以，功效與作用強，靠受得了高朝。

This equipment’s electrical system consists of PLC (Programmable Logic Control), contactor, frequency converter, servo system, motor and different kinds of detecting sensor. The controller is used series M218 of Schneider, which is small, fast, reliable, standardizing and has ability of serial communication.

裝備的操縱形式

Equipment’s Operation Mode

設備主機有拒絕和手動不同任務體例，沿途流程扳動“拒絕/手動”退出區分。The main machine has two kinds of working mode--- auto and manual, which can choose by turning the “auto/manual” button.

1手動形式

Manual Mode

零丁操作設備法寶的任何工作方案，以及操作人員的物品研究生調劑和法寶保證。Operate every single action of main machine to make operator easy to adjust and maintain equipment.

2主動形式

Auto Mode

隨著確定性的西式停機積極主動命輪，操作者只目前裝料、下料機便可。Work circularly and automatically by the set process, the operator only needs to load and unload material.

聯動/單動

single/linkage

冷水機和自覺放料企業有互通和單動兩者釣魚任務體例，所經的過程扳動“互通/單動”中斷在挑選。There are two working mode for main machine and automatically feeding device--- single and linkage, which can be chosen by turning “linkage/single” button.

單動形式

single mode

在會去被動結構類型下，只是彩打和卷圓機、壓平機會去被動天道輪回，包涵裝料中介機構。Under the auto mode can only circularly work stamper and flattener without feeding device.

聯動形式

linkage mode

在積極自覺結構下，在打印出和卷圓機積極自覺命輪中改變積極自覺送料機作用與功效，人工就是將料垛加在送料機小車子便可。Under the auto mode, add automatically feeding function to automatical circle of stamping and coiler, worker only need to put material on the feeding dolly.

說話切換

Language

按“聊天說話設置”后顯現出如上圖所述，開始漢英文翻譯設置。Click “language” to get into the interface like above picture, where can choose language between Chinese and English.